|
Home
Firearms,
Accessories,
Hunting, etc.
Shop On Line
Original
Site
For
The
Ladies
Gun
Rules
Contact Us
Phone 281 300-3292
Fax 281 596-6952
|
|
Assembly
Instructions for AK/MAK-90/MAADI Fiberforce Stock
|
|
AK/MAK-90/MAADI
Fiberforce Stock
Part#MAK0100
|
|
Fits 7.62x39mm AKs, Mak-90s and MAADIs.
|
***MAKE SURE YOUR RIFLE IS UNLOADED BEFORE STARTING***
All screws must be lubricated prior to assembly.
STEP #1 Inspect magazine and chamber to be sure they are
empty. Remove receiver dust cover, recoil spring, and bolt assembly per
manufacturer's instructions.
Remove Buttstock
Buttstocks will be held in place with two (2) or three (3) screws
depending upon model. Remove the one (or two) screws from the receiver
upper rear tang. An additional screw may also be found running upward
through grip. The third screw on the Maadi is removed from inside the
receiver, it is a wood screw running into the top of the pistol grip.
You should now be able to remove butt stock.
|
|
|
STEP #2 To remove gas tube/handguard assembly: Raise lever on
right side of rear sight base. The assembly can then be removed by
lifting upward on the rear end. To remove the wood from the assembly,
rotate the wood around the gas tube 180 degrees and lift it off.
STEP #3 To remove the lower forearm wood: Raise the small
locking lever located inside the right side of the forearm front barrel
band. Rotate the locking lever 180 degrees forward - as far as possible.
The barrel band should then slide forward releasing the front of the
forearm.
|
 |
STEP #4 To install new lower forearm: Insert lower forearm
rear locator tab into recess in front of receiver. While holding front
of forearm against barrel, work barrel band rearward over front of
forearm. Then return the barrel band locking lever to the locked
position. (Reverse Step #3).
|
|
|
STEP #5 NOTE: To ease assembly/ disassembly, all screw threads
must be thoroughly lubricated prior to installation. To install new
upper handguard: First install gas tube (minus wood) by reversing
removal process. (Reverse Step #2). Install upper handguard by inserting
front of handguard into barrel band. Gently tap upper handguard forward
until it drops in place. Install the two (2) provided #6 self tapping
screws.
Caution: Do not over-tighten.
|
 |
STEP #6 To install buttstock: Slide buttstock into place on
receiver. Make certain buttstock is as far forward as it will go.
A. MAK-90- install the 6mm socket head cap screw upward through
bottom of grip. Note: If your MAK-90 has the loose/floating tee nut, use
your original 6mm grip screw threaded temporarily into the back side of
the tee nut to hold the tee nut in place until you get the grip screw
started. Tighten grip screw. Caution: Do not over-tighten.
B. MAADI - Install the large self tapping bolt and washer
downward thru the square hole in the receiver and into the hole in the
butt stock. Caution: Do not over-tighten. IN BOTH CASES, INSTALLATION OF
THE NEW BUTTSTOCK IS A REVERSAL OF THE REMOVAL OF THE WOODEN STOCK.
NOTE: To ease assembly and disassembly all screw threads must be
thoroughly lubricated prior to installation. |
|
NOTE: Holes for tang screws are not pre-drilled due to
differing mounting locations in manufacture of MAK90/MAADI rifles.
|
STEP #7 The receiver tang screw hole (holes) can now be
drilled. FOR MAK90 use 13/64” drill bit. FOR MAADI use 3/16” drill
bit. Install the original tang screws.
Note: A small amount of lubrication will ease the initial screw
installation. Caution: Do not over-tighten.
STEP #8 Reinstall the bolt / gas piston assembly and dust
cover per manufacturers instructions.
|
©2002
Advanced
Technology,
Inc
.
|
Welcome to RB's Treasures. 
