Featured Treasures

Mauser 98 Stock with Built-in Scope Mount
Part#MSS1500

Fit all LARGE-RING, Standard BENT-BOLT Mausers 98s. Partial list includes German K-98, Czech VZ-24, Yugo 24/47, Yugo 48/48A, Turkish 1903/1937/1938/1946, etc...It is designed to be used with a rifle scope ONLY!
Will NOT fit large ring Swedish Mauser M38/M96 6.5x55 or SMALL ring Mausers, (Spanish M1916 .308) etc...
Fits barrel diameter .950 to .990".

Includes a Built-in Scope Mount for multiple positioning of rifle scopes.

VERY IMPORTANT: To mount a scope on the rear, it is necessary to convert Straight-bolt and "Wide-arc" bolts to bent bolt with Mauser Bolt Handle Part#MBH-1800. To mount a long-eye relief scope forward, any bolt handle will work.

***MAKE SURE YOUR RIFLE IS UNLOADED BEFORE STARTING***

STEP #1
Determine if the Advanced Technology Bolt Handle conversion is necessary. Install now, if needed. To mount a scope on the rear, it is necessary to convert Straight-bolt and "Wide-arc" bolts to bent bolt with Mauser Bolt Handle Part#MBH-1800. To mount a long-eye relief scope forward, any bolt handle will work.

STEP #2 Important...note the location of the serial number on your Mauser. Use a file or dremel tool to remove stock material so that the serial number will be visible after the stock is installed.

STEP #3
Remove the barreled action from the existing stock. Then remove handguard from the barreled action.

STEP #4 Remove Rear Sight
Example (A): Drive out retaining pin, then push the front of the sight downward and pull rearward to remove sight.
Example (B): Drive out retaining pin, then use small punch and tap the spring toward the front sight. Then lift out rear sight.
Note: These are only two examples for rear sight removal.

STEP #5
Place clamps (included) on barrel between receiver and the rear sight bracket as shown, with the top (4) threaded holes "UP", and the side (4) threaded holes to the left of the receiver. Install and tighten the (2) 10 - 32 x 1/2" Socket Head Cap Screws (SHCS) in the counterbored holes at the top and place the (2) 10 -32 x 3/4" Socket Head Cap Screws in the lower side holes but do not tighten. Place the scope rail over the clamp. Install and tighten the (4) 8-32 x 1/2" Socket Head Cap Screws.

STEP #6
Place the barreled action with the scope rail and clamp into the stock. Align the scope rail as necessary by rotating slightly or moving back and forth. Once properly aligned, remove barreled action and scope rail from the stock and tighten the bottom (2) 10-32 x 3/4" Socket Head Cap Screws. This "locks" the Scope Mount Clamp on the barrel.

RECOIL SPACER

STEP #7
The recoil lug spacer allows various Mausers to fit this stock. Place the action into the stock. Reinstall and tighten both original barreled action mounting screws. Observe oblong hole in stock and check for gap. If the gap in the oblong hole is to the rear, then the recoil spacer must be installed. The object is to ensure full contact between the recoil lug and the stock. Remove the action from the stock. Insert recoil spacer, if required, into the matching holes in the stock.

STEP #8
Remove the spring and follower from the old trigger guard/magazine by grasping the bottom of the spring and pulling rearward, free of its retaining grooves. Place the spring inside the magazine-well, with the shell-follower face-up.

STEP #9
A. Place the barreled action with the scope rail back into the stock. Place supplied 1/4" washer over front action mounting screw and install. Tighten both screws. Install rear action mounting screw.

B. Place the (2) #6 x 1" screws into the rear holes on the scope rail and partially tighten into the stock.

C. Lay rifle on its side, place the (2) #8 x 2" screws into the front underside holes in the stock. Visually align the tip of each of the screws into the holes on the scope mount. Tighten all 4 screws.

Caution: If these screws are installed "crooked", they can "breakout" the side of the scope mount. Also, do NOT overtighten these #6 x 1" or #8 x 2" Screws.

Installation is now complete.